Commando FM-870 Owner's Manual Page 11

  • Download
  • Add to my manuals
  • Print
  • Page
    / 17
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 10
JAN/07/2003
RST872
11
REMOTE START OPERATION:
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button twice on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking light will turn on again
and climate controls will activate and adjust the vehicles interior temperature to your
preset setting. (While the vehicle is running, the “minutes” digit on the LCD screen
will flash and the will indicate count down timer based on the 5, 10, 20 or 30 minute
run time set up by your installation center.)
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down.
(When the unit shuts off the count down timer will turn off and the transmitter will
play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
Activate Remote
Start
Engine Running
SAFE START (Child safety mode) (See Start Feature I – 5 Programming.)
Factory defaults setting to press the
button twice on the transmitter to start the vehicle. Programming
this feature to eliminate an accidental remote start, when kids enter this transmitter, it requires:
The user press the transmitter
and buttons at the same time to start the vehicle.
B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START:
To operate the vehicle while engine running on the remote start.
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but
would like to leave the motor running and the climate control on.
1.Before turning off the engine, press the
button twice on the transmitter and the LED indicator will
flash 3 times to confirm enter.
2.Turn the ignition key to OFF position. (The engine will stay running.)
3.The engine will run until the pre-programmed time elapsed or shutdown input is received.
D. TIMER / TEMPERATURE START:
This unit can be programmed to start and run the engine every 3 hours or punctually at the same time next
morning, The engine will run for the programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, Never start and run the vehicle in on
enclosed space as a garage or carport.
3 hours timer start with Temperature-control OFF: This feature is design for an extreme cold climate
usage. The system will auto start the vehicle every 3 hours, to prevent engine freezing and hard to start.
A MAXIMUM OF SIX CYCLES CAN OCCUR.
3 hours timer start with Temperature-control: (See Start Feature
I – 8 Programming.)
If you installed the optional Temperature Sensor and programmed the temperature ON to operate. The
system can be programmed to automatically start the vehicle engine whenever the temperature inside the
vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air
temperature every 3 hour and will only start the engine during extreme cold temperatures. There are three
temperature level to choose form.
Daily Timer Start: The feature is very useful for the driver who wants to run the vehicle punctually at the
same time next morning. Before set-up of the “Daily Timer Start”, you should set you time for engine
start.( see Timer Setting /
Timer set-up for “Daily Timer Start, page 16)
ENTER:
1. Press the
button twice to remote start the vehicle. As soon as the vehicle is running and the parking
light have turned on or flashing.
Page view 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17

Comments to this Manuals

No comments