Commando FM-870 Installation Manual download pdf (Page 15)

FEB.20, 2003

RST872

PROGRAMMING

A. PROGRAMMING TRANSMITTER:

PROGRAMMING THE REMOTE TRANSMITTER

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is

exceeded, the security system will start deleting transmitters from memory in chronological order.

Enter:

1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.

2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You

are now in the Transmitter programming mode.

Program:

1. Press button on one of the transmitter until the siren responds with a confirming chirp the first transmitter

is now programmed.

2. Press button on the second transmitter until the siren responds with a confirming chirp, the second

transmitter is now programmed.

3. Apply the same procedure to program 3rd and 4th

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to

confirm exit.

B. FEATURES PROGRAMMING:

ALARM FEATURE “I” PRORAMMING:

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2. Push the Valet switch

2 times and hold it until one chirp with a long chirp is hearing then release the valet

switch. You are now in the Alarm feature

‘I’ programming mode.

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.

a. The siren chirps and LED pause will indicate previously setting.

b. The factory default settings is always [1] LED flash, [1] chirp.

4 Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the transmitter

button ‘A’ again until the module advances to your desired setting.

a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps.

b. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.

5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.

For example: To program the arming mode form “Active arming” to “Passive Arming without Passive Door

Locking”, After “Arming mode” program, the next program is “Rearm on/off” .……….

1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.

2 Push the Valet switch 2 times and hold it until a chirp with a long chirp is hearing then release the valet

switch.

3 Press and release the transmitter

button corresponding to the feature ‘Arming mode’ you wants to

program. [1] LED flash, [1] chirp to indicate your are in features “Active Arming”.

4 Depress the transmitter

button twice to change the feature. [3] LED flash, [3] chirps to indicate your

are in features “Passive Arming without Passive Door Locking ”.

5 Depress the transmitter

button corresponding to the features ”Rearm on/off”’ you want to

program……..

Press

Transmitter

Button

One Chirp /

LED one pulse

Factory Default

Setting

Two Chirps /

LED two pulses

Three Chirps /

LED three pulses

Four Chirps /

LED four pulses

All chirps on Siren chirp on only Horn chirp on only All chirps off

Active arming Passive arming

without passive door

locking

Passive arming

with passive door

locking.

Automatic Rearm

Automatic Rearm off

3 seconds delay

Door Ajar error

chirp

30 seconds delay

Door Ajar error chirp.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 24 25

Comments to this Manuals

No comments

Commando FM-870 Installation Manual Page 15

Comments to this Manuals

Related products and manuals for Remote starters Commando FM-870